# AIO, Current sensor V5.7

**URL:** <https://discourse.agopengps.com/t/aio-current-sensor-v5-7/11436>\
**Category:** Uncategorized\
**Created:** [1 February 2023 14:34 UTC](https://discourse.agopengps.com/t/aio-current-sensor-v5-7/11436 "2023-02-01T14:34:37Z")\
**Posts on this page:** 9\
**Page:** 1

<div class="post-metadata">

**Author:** ![TeddyStamford](https://discourse.agopengps.com/letter_avatar_proxy/v4/letter/t/76d3ee/32.png) [@TeddyStamford](https://discourse.agopengps.com/u/TeddyStamford)\
**Post date:** [1 February 2023 14:34 UTC](https://discourse.agopengps.com/t/aio-current-sensor-v5-7/11436/1 "2023-02-01T14:34:37Z")

</div>

AIO V5.7 latest firmware installed, the Steering current sensor when at rest reads 52% and when steering hovers around the 50% mark.

I set the current sensor to turn steering off at 60%, yet when I grab the wheel the steering current goes down to around the 30% mark.

Is this a known problem?

---

<div class="post-metadata">

**Author:** ![Jhmach](https://discourse.agopengps.com/letter_avatar_proxy/v4/letter/j/ed8c4c/32.png) [@Jhmach](https://discourse.agopengps.com/u/Jhmach)\
**Post date:** [1 February 2023 14:47 UTC](https://discourse.agopengps.com/t/aio-current-sensor-v5-7/11436/2 "2023-02-01T14:47:14Z")

</div>

There was a change in the ino to fix that. I think it will be in the next release today or tomorrow

---

<div class="post-metadata">

**Author:** ![TeddyStamford](https://discourse.agopengps.com/letter_avatar_proxy/v4/letter/t/76d3ee/32.png) [@TeddyStamford](https://discourse.agopengps.com/u/TeddyStamford)\
**Post date:** [1 February 2023 15:22 UTC](https://discourse.agopengps.com/t/aio-current-sensor-v5-7/11436/3 "2023-02-01T15:22:19Z")

</div>

Brilliant, thanks.

---

<div class="post-metadata">

**Author:** ![Jhmach](https://discourse.agopengps.com/letter_avatar_proxy/v4/letter/j/ed8c4c/32.png) [@Jhmach](https://discourse.agopengps.com/u/Jhmach)\
**Post date:** [1 February 2023 17:17 UTC](https://discourse.agopengps.com/t/aio-current-sensor-v5-7/11436/4 "2023-02-01T17:17:49Z")

</div>

I did confirm that the pressure sensor code has been fixed in 5.7.1.

---

<div class="post-metadata">

**Author:** ![Gunfigter100](https://discourse.agopengps.com/user_avatar/discourse.agopengps.com/gunfigter100/32/8666_2.png) [@Gunfigter100](https://discourse.agopengps.com/u/Gunfigter100)\
**Post date:** [16 March 2023 01:36 UTC](https://discourse.agopengps.com/t/aio-current-sensor-v5-7/11436/5 "2023-03-16T01:36:19Z")

</div>

Does the version of the ACS712 make a difference in how the percent amperage is measured? I have the 30A version of the ACS712 and my current reading is hovering around 5% under normal operation and rising to 8-9% when I grab the motor gear. I am still testing on the bench at the moment so I don’t know if having it hooked up in the tractor will make a difference or not. From what I have read on these forums it seems most people are using the 20A version of the sensor. If the Amp version of the sensor does make a difference, is there a change to the autosteer .ino code that would make it work better or is it better to get the 20A version of the board?

---

<div class="post-metadata">

**Author:** ![m\_elias](https://discourse.agopengps.com/letter_avatar_proxy/v4/letter/m/94ad74/32.png) [@m\_elias](https://discourse.agopengps.com/u/m_elias)\
**Post date:** [16 March 2023 03:26 UTC](https://discourse.agopengps.com/t/aio-current-sensor-v5-7/11436/6 "2023-03-16T03:26:38Z")

</div>

It absolutely makes a difference! Your 20A is scaled for -20A to +20A equals 0-5V output. 0A = 2.5V  
A 5A does the same with -5 to +5. So putting 2A through a ACS-20 will only get you from 2.5V up to 2.75V

---

<div class="post-metadata">

**Author:** ![Ray\_Jorgensen](https://discourse.agopengps.com/user_avatar/discourse.agopengps.com/ray_jorgensen/32/7635_2.png) [@Ray\_Jorgensen](https://discourse.agopengps.com/u/Ray_Jorgensen)\
**Post date:** [16 March 2023 10:28 UTC](https://discourse.agopengps.com/t/aio-current-sensor-v5-7/11436/7 "2023-03-16T10:28:17Z")

</div>

So which to get - 5, 20 or 30 amp?

---

<div class="post-metadata">

**Author:** ![Gunfigter100](https://discourse.agopengps.com/user_avatar/discourse.agopengps.com/gunfigter100/32/8666_2.png) [@Gunfigter100](https://discourse.agopengps.com/u/Gunfigter100)\
**Post date:** [17 March 2023 00:38 UTC](https://discourse.agopengps.com/t/aio-current-sensor-v5-7/11436/8 "2023-03-17T00:38:24Z")

</div>

I’m using the 12V to 24V converter on my build which has a 10A max output according to the label on it. So I am assuming the 20A version would be the way to go since the 5A version could potentially be fried by the converter.

---

<div class="post-metadata">

**Author:** ![Pat](https://discourse.agopengps.com/letter_avatar_proxy/v4/letter/p/8491ac/32.png) [@Pat](https://discourse.agopengps.com/u/Pat)\
**Post date:** [17 March 2023 03:04 UTC](https://discourse.agopengps.com/t/aio-current-sensor-v5-7/11436/9 "2023-03-17T03:04:16Z")

</div>

The 5A sensor will survive up to 25amp, his output is optimized for 0-5A. should work for most cases  
the 5A is 187mv/A theorically this gives reading up to 13A but the chart stops at 5, so I don’t know what happen to the reading above 5A  
the 20A is 100mV/A

> **[ACS712ELCTR-05B-T | Allegro MicroSystems, LLC | Current Sensors | JLCPCB](https://jlcpcb.com/partdetail/45473-ACS712ELCTR_05BT/C44471)**
>
> ACS712ELCTR-05B-T from Allegro MicroSystems, LLC - Current Sensors is available for JLCPCB assembly, check the stock, pricing and datasheet, and let JLCPCB helps you assemble the part ACS712ELCTR-05B-T for free.
