Hydraulic valve assemblies for Every tractor, for every type of hydraulic system

[RMiedema1999]

I have a small question, can the 3/2 valves be powerd while manual steering?

Or sould the power be cut while manual steering?

[Larsvest]

@RMiedema1999

can the 3/2 valves be powerd while manual steering

No Steering wheel is absolutely locked when 3/2 valves are powered.

[RMiedema1999]

@Larsvest

No Steering wheel is absolutely locked when 3/2 valves are powered.

Good to know!
In that case, i have to change my idea for powering everything

Any ideas how to connect everything with a AOGpcb v2?

[Raycorp]

I used pin D2 i think to power a 5v relay when press steering button. 12v send true relay to enablers.

Just a lil code change in the .ino

[Raycorp]

I can check tommrow if you want.

[Larsvest]

@RMiedema1999

AOGpcb v2?

It is already there.
Pwm2 by the connectors to cytron
Last picture in post 1

Wiring diagrams

As part of the documentation we have created this post to have grouped all the wiring diagrams for the PCB. We use the Kaupoi 4.1 PCB for the diagrams, but it can be used for any current PCB, you just have to look at the names of the connections on the PCB. The only difference is that the Kaupoi 4.1 has a slot for the Adafruit BNO085 and a slot for the CMPS14. Later you will find diagrams to connect any BNO08x that is not from Adafruit. The difference between the BNOs is that Adafruit uses a v…

or look on github in AgOpenGPS_Boards-master
Look for Misc/wirings

[RMiedema1999]

@Raycorp

I can check tommrow if you want.

Need to order a valve first

[RMiedema1999]

@Larsvest

Last picture in post 1

As part of the documentation we have created this post to have grouped all the wiring diagrams for the PCB. We use the Kaupoi 4.1 PCB for the diagrams, but it can be used for any current PCB, you just have to look at the names of the connections on the PCB. The only difference is that the Kaupoi 4.1 has a slot for the Adafruit BNO085 and a slot for the CMPS14. Later you will find diagrams to connect any BNO08x that is not from Adafruit. The difference between the BNOs is that Adafruit uses a v…

or look on github in AgOpenGPS_Boards-master
Look for Misc/wirings

Thanks

[ansu]

[Bullhill]

Will you get back to us who sendt you email when you where short on supplys or do you want a new email?

[hachtoy]

hello, no I haven’t connected the pressure sensor yet, I just wanted to test the hydraulics and the solenoid valves. I finish my pcb box and I finish the connections. the pressure sensor will cut the solenoid valve and unlock the steering wheel?

[timoy]

Yes pressure-switch connected to remote pins is used to release solenoids

[pAy]

Hello, can you tell me the schedule for the deliveries? When will you be able to ship the items ordered now?

[AlexanderL]

Hello, so Marek seems pretty busy.
Can anyone tell me, if i need a Kaupoi PCB for the valve or is included or are there better options than the kaupoi. Brian said they are working on something.

[m_elias]

The PCB is a separate part from the valve. Most PCBs support using a Cytron (except for can bus only PCB).

[AlexanderL]

do i even need a PCB then?

[Bullhill]

You need a Nano to control the cytron, and somewhere to connect the wheel angle sensor, pressure sensor from valve block and optional buttons for autosteer enable etc

[AlexanderL]

Yeah, i got a nano and an ADS for the WAS. The button is connected to the Nano.
What do i need for the pressure sensor? Or can i connect that with the nano too?

[Larsvest]

@AlexanderL

sensor? Or can i connect that with the nano too?

Some others have tried without pcb.

Help with steer motor

With no PCB it is easy to make a mistake in the wiring. SLC and SDA pins are the same for old and new designs (version 4 and higher for sure) If the arduino program does not match the version, then steering part is not going to work. Also, if the WAS is not connected or wrong signal, steering won’t start.

[ipeel8]

@ baraki. Ok so I have a Baraki LS valve and a standard ampseal aio pcb. I have a few questions.

1. If I hydraulically hook the valve up without hooking it up electrically am I still able to steer the machine manually with the steering wheel?
2. The valve I recieved doesn’t look like the valve on post #261 is the wiring still the same? When I hook the valve up electrically does the polarity on the solenoids matter?
3. I have schottky 15amp 45v diodes are they an appropriate size or is a different schottky size required?
   Thanks