All in One PCB

Hardware
489

image
image354×513 16.6 KB

This is the tht equivalent
In easyEDA, if you right click on the green THT part in the trace with the SMD it will give you the part numbers

1 Like
490

MOTOR Guys
I have edited the Micro PCB and made the traces heavier for the motor guys. Also have removed the CAN bus components and suppressed the Danfoss components, for a more basic all in one for the motors.
It is newly finished and untested, though there are not a lot of changes. To run motors it will need some 16 gauge insulated wires soldered in as jumpers since there is no board space left to get the traces large enough for the higher currents.

image
image728×830 244 KB

The light blue lines from R/L to the cytron.
The other light blue line is for using 12V in from the board power. If using external 12V or 24V, use the darker blue path and power the cytron at pin 16 of the AMP connector. The 24V jumper will need soldered for all motors and the 12v must be left unsoldered.

https://drive.google.com/drive/folders/1usCFJvlXnaOCqDf0f4bx8o_yOgFUw9XZ?usp=share_link
EDIT
NO more solder jumpers. The google link has been updated

image
image649×810 271 KB

EDIT
Labels on Left/Us and Lock/Right were corrected
Google Drive is updated
image
image728×893 247 KB

2 Likes
491

I think there’s a slight silkscreen error on the micro board.
image
The cytron Us-or-Cytron LEFT should be the other way round, i.e. Cytron LEFT-Or-Us.
It’s correct on the standard board. Same problem with LOCK or RIGHT by the looks of it.

It just means the jumper needs to be the other way round

492

I changed it and didn’t save it again. I will fix it. Thanks

Edit
Labels Fixed

493

Correction only for the micros or for the standards?

494

I haven’t looked at the standard, but I should.

2 Likes
495

Anyone selling the all in one pcb for the big f9p
?

496

I have a few left with the Ampseal23 connector & harness. I mostly ship to Canada and the US. If you’re interested, send me a PM and I’ll get you pricing details.

edit
I’m all out of PCBs

497

2SC2884Y (JLCPCB Part#C475474) will be a suitable replacement for smd?

498

If it helps others, this is the correct part to substitute Q3 on the Standard AIO PCB, from Digi-Key,

2 Likes
499

Just kinda curious. But why did they chose to use all of those separate modules and through hole components? Wouldn’t it have been more compact and cost effective to replace most of them with SMD components?

500

Because these days, half the time you can’t get all the smt parts, so now at least there’s still the tht parts to getting it going.

501

I am getting RTK Fix In AOG, sentence seems to be correct yet the RTK led on the PCB stays red. Is there any possible reason for this?

I’m getting the same…from the code:
#define GPSRED_LED 9 //Red (Flashing = NO IMU or Dual, ON = GPS fix with IMU)
#define GPSGREEN_LED 10 //Green (Flashing = Dual bad, ON = Dual good)
So it will be solid red for single setup like us.
If the dual receiver guys flexing on you offends you then you could modify the code below by swapping the high and low. (zHandlers tab)

*if (!useDual)*
*       {*
*        digitalWrite(GPSRED_LED, HIGH);    //Turn red GPS LED ON, we have GGA and must have a IMU     *
*        digitalWrite(GPSGREEN_LED, LOW);   //Make sure the Green LED is OFF     *
*       }*
502

I guess that makes sense. But what about the adafruit modules and even the F9P? Would it not be pretty easy to add them all the the board?

503

Could someone put up what setting they are using and antennas placement and the agopen measurements for dual antennas

504

Thanks for this, makes sense. Currently a dual user with PCB v2 but was planning on a new setup with the AIO with a single f9p. Not sure whether there is any benefit with dual with the AIO, perhaps better roll and direction detection?

505

i think it would be nice if you did the same with the standard f9p all-in-one board, since a lot of people still use the electric motor without the can system. I believe that in the French telegram someone has suppressed the can and the danfos, but has not published the files yet.
Thank you very much for all these works from which many members of the community benefit, including me.

506

Hi!

What is ByNav? Do we need it for one antena use?

507

Maybe it’ll help someone. I guess this is the U8 and U903 headers:

Am I wrong?

508

I orded this.

Can’t get my motor spinning