Only tried single, I do not see that was reading flicker.
1 Like
I have it on single as well, tried differential but the readings were way off, only curious as to what you found. Thanks.
Is it possible for you to re-host your photos please?
They are all in the onedrive link. But you should definitely go for the fivefinnishfarmers way of doing this. He did it better.
Hey larsvest, I have question. I use BNO08x any I have problem with heading. Everything else seems working good but heading is working weirdly when I turn. When I go straight error between fix2fix and IMU is about 1° but when I start turning, firstly IMU heading acts slowly and when I finish 180° turn with tractor heading keeps turning so when I go straight after turn IMU heading thinks I´m still turning and the error rise for a while about 5°. So the result is that tractor goes straight but agopengps thinks tractor is heading little bit to the side.
I have only one Arduino on which is everything connected via one USB. Can you help please? Thanks.
How it looks after 180° turn when going forward:
You are right, that is how it works normally.
But some people have been working on a solution.
I think you then need a teensy!
Check you fix/fix distance and make sure it’s not too big (less than 2.5m max). Also move the IMU/GPS fusion slider closer the GPS side
1 Like
Oh thanks. And how it works with CMPS14? Does need cmps teensy?
BNO08x is better than CMPS so stay with your BNO08x.
1 Like
What is the easiest way to tell if my t6.175 is autosteer ready?
Several ways actually.
Hydraulic valves on the line from orbitrol to steer cylindets.
An autosteer switch on right post in cab.
Wire harness ending on top of cab (outside center at back top)
Wire harness ending under left corner cover , ending in two quite big connectors.
There are more.
The t6 175 I worked on had factory mounted the extra autosteer harness.
No switch on the pillar…so it’s not autosteer ready?
Unfortunate!
Probbably not… but I am working on my t6 165 with no autosteer ready, later when I finnish it I will add it to success projects and I will also make video how I build it. T6 175 and T6 165 are pretty much the same.
1 Like
Brilliant!
Looking forward to it. Are you using one of Baraki’s valves?
Yes my friend, it is gonna look like this:
Right now, I am going to make hoses, with my friend, to connect the orbitrol with Baraki´s block.
2 Likes
hi, I would like some help, a New Holland Tg230 tractor was factory installed with an AgGPS Autopilot Trimble system with an eaton-vickers hydraulic valve. There is an override hydraulic control valve next to the orbit. What function does this valve perform? Can I connect to Aog?
Hello guys, I have question. How to propperly place BNO? I have it mounted like on first picture but FIX and IMU shows different numbers is it OK? I guess that numbers should be quite same or am I wrong?
I am running Panda on teensy on my setup everything works fine just that IMU.
When I rotate BNO about 45° the numbers FIX and IMU in upper left corrner shows quite same numbers but I cant read propperly roll or am I wrong? Picture of rotated bno:
And if I change setting “IMU X or Y Axis” to Y nothing changes.
What can be wrong guys? And should be that numbers as much same as possible?
The IMU number is 0 when the BNO is first powered up. Point the tractor North and power cycle the BNO and the number will match the fix number. The absolute values do not need to match at all, only the IMU delta is used. If both numbers increase in the same direction by the same amount then the numbers are working properly.
1 Like
You can get correct roll only by using x or y direction. Or change to dual receiver setup where roll come from GPS. With dual you can rotate imu around z as you you like.
1 Like
Yes thats a pressure sensor in the counterbalance valve. Sweet thing is you can use all the cables from the Trimble harness.
Is the nav controller still inside? And the main harness?